Thursday, 10 June 2021

Renovating a Morgan Roadster 100 Hood

Renovating a Morgan Roadster 100 Hood

By David Owens

Cleaning, Re-colouring and Water Proofing an R100 Hood

Tools Required

  1. Phillips Screwdriver

  2. Masking Tape

  3. Newspapers

  4. Sheets

  5. 2 X 3” Paintbrushes

  6. Sponge

  7. 2 Containers – Empty Ice Cream Tubs work fine.

  8. Renovo – Cleaner, Colour Reviver, Ultra Proofer – 500ml each. I bought off Ebay for 38.95 GBP.

  9. https://www.renovointernational.com/car-care/soft-top-reviver.php

Step 1

  • Lightly rinse the hood, hood cover, sidescreens and sidescreen bag.

  • Apply Renovo Cleaner with a sponge rub in well and leave for 20minutes.

  • Rinse off all of the items and leave to dry.

  • Undo the three Phillips screws holding on the mohair panel on each sidescreen.

Step 2

  • Mask off the car windscreen, rear screen and sidescreens using the tape and newspapers.

  • Cover the rest of the car with old sheets. This is probably overkill.


Step 3

  • Pour the Renovo Colour Reviver into a container and starting at the centre, using a 3” paint brush, apply the colour to the hood. One coat should be enough.

  • Do the same to the hood cover, sidescreen bag and sidescreen panels. The latter two will need to be done in two stages as they need colouring on both sides.


Step 4

  • After 24 hours repeat Step 3 with the Ultra Proofer.


Step 5

  • Once the hood is dry remove the sheets, newspapers and Masking tape.

  • Clean the aluminium frame of the sidescreens (Optional) before screwing the side panels back on.



All in all a simple but time consuming exercise but I am very happy with the results.

Notes – There was plenty of cleaning solution left for further cleaning at a later time. There was just enough colour reviver for the one application. There was a very small amount of Ultra Proofer left and if I was doing it again I would get one litre of the Ultra Proofer as what would be left would be enough to do the hood another two times at six month intervals.




The Products that David used.


Renovo Soft Top Reviver

Re-Colours and Re-Conditions Your Soft Top

Description

This unique and innovative formula is simple to apply and gives unbelievable results - even when the fabric soft top is severely faded on your new or classic car.

We recommend using Renovo Fabric Soft Top Cleaner according to the ‘severely soiled’ instructions on the bottle to thoroughly clean your convertible top prior to applying Soft Top Reviver. It is important to ensure that the fabric is free of grease, dirt and any previous waterproof coatings before using Soft Top Reviver.

After reviving the colour, many of our customers extend the longevity of the makeover by applying our weatherproofing Ultra Proofer too.
Renovo Soft Top Reviver is available in Black, Dark Blue, Dark Green, Dark Red or Dark Brown and is quite literally a new soft top out of a bottle.
Although originally created for soft tops, the Soft Top Reviver is also ideal for boat covers, canvas, double duck, and mohair coverings as it re-colours and reconditions them all like new.

Please Note: Purely as a guide, the Dark Red is mixed to Pantone 202C, Dark Green is mixed to Pantone 5467C, Dark Blue is mixed to Pantone 282C and Brown is mixed to Pantone 4625C.



Fabric Soft Top Cleaner

For Regular Soft Top Cleaning

Description

For regular cleaning of canvas, double duck and mohair convertible soft tops of all colours, freshening appearance and helping to preserve the soft top's overall condition. THE best convertible roof cleaner!
Fabric Soft Top Cleaner removes grime and ingrained dirt without impairing the appearance of the convertible car's fabric and is suitable for all colours.

Fabric Soft Top Cleaner is recommended for preparation of the convertible hood before application of Soft Top Reviver and Ultra Proofer. It is especially important to ensure that the fabric is free of grease, dirt and any previous waterproof coatings before using Soft Top Reviver! Ultra Proofercan still be applied with residual waterproofing agents within the material, but it should be thoroughly cleaned with Fabric Soft Top Cleaner to ensure that dust and dirt will not be sealed into the fabric.

How to Clean a Convertible Top

Please note: It is advisable to test on an inconspicuous area first, to ensure fabric is colourfast dyed. Never use pressure washers on soft tops.

Normal Cleaning

  1. Dry brush the soft top to remove any residual dirt.
  2. Dampen surface of Soft Top with a mist spray of water or a damp sponge.
  3. Shake bottle well prior to removing top.
  4. Pour into suitable container.
  5. Apply with a clean 5cm/2" paint brush using even brush strokes. Start at the centre of the cover working out towards the edge.
  6. Leave for 10-20 minutes to ensure the cleaner can work on difficult grime and stains.
  7. Commence scrubbing using warm water and a sponge, cloth or bristle brush until the cleaner begins to lather and dirt is being removed easily. Finish by rinsing off with water. Repeat the whole process if necessary.

For heavily-soiled surfaces leave the solution to dry for approximately 60 minutes - the optimum time for active ingredients to work. Heavily-soiled surfaces should be scrubbed with a bristle brush. Finish by rinsing off with water. Repeat the whole process if necessary.

Finally leave to dry before applying Renovo’s Ultra Proofer which will not only re-establish the original 'as new' waterproof weather barrier on your canvas, double-duck or mohair convertible top, also now contains UV protection and a mould/mildew growth inhibitor.

Bird Droppings / Difficult Stains

Dab or pour the Cleaner directly onto the spot of dirt or stain. (Massage into the affected area) Clean off after 30 mins. Repeat process if necessary.

Light Soiling / Quick Cleaning

For less soiled tops cleaning can commence immediately. Pour directly onto on to a cloth or sponge and massage into the affected area. Rinse off with water.

As with all cleaning products, it is best to avoid prolonged contact with skin. It is advised to use rubber gloves for protection.

We advise that to prolong the life of the re-colour provided by Reviver, you should allow 24 hours drying time and then protect it by applying Renovo Ultra Proofer.

Soft Top Reviver - Application Instructions


Please note: Do not dilute or mix Reviver with any other product! This would seriously impair the product performance and may damage your car.

  1. Ensure that the soft top is dry and free from grease, dirt and previous waterproof coatings by thoroughly cleaning with Renovo Fabric Soft Top Cleaner before commencing application.
  2. Unscrew the bottle top and pour Reviver into a suitable container/bowl.
  3. Stir well prior to application
  4. Apply Reviver with a new 5cm/2inch paintbrush using even strokes across the soft top. It is best to commence application in the centre of the soft top and as quickly as possible progress towards each side, the front and the back of the soft top. Wipe excess drips from paintwork, trims and glass with a damp cloth. Do not apply in direct sunlight, as this will cause the Reviver to dry out too quickly and produce an uneven result!
    Depending on the condition of the top a litre of Reviver is usually sufficient for two coats on an average size soft top. It is important to allow Reviver to dry between coats. Always ensure that you have enough Reviver to coat the soft top completely and that you will not run out half way through application!
    Renovo recommends applying at least two coats to achieve greater depth of colour on badly faded tops.
    Reviver can also be applied in the same way as above to the fabric on the interior of the top.
  5. Allow the top to dry for approximately three hours, this will depend on the drying conditions. The Reviver may dry out more quickly if it is a warm day and may take longer to dry if it is a damp day! Do not take the car out in rain/wet weather until the Reviver has completely dried.
  6. We advise that to prolong the life of the re-colour provided by Reviver, you should allow 24 hours drying time and then protect it by applying Renovo Ultra Proofer!
  7. Wash out brush in warm soapy water

We advise that to prolong the life of the re-colour provided by Reviver, you should allow 24 hours drying time and then protect it by applying Renovo Ultra Proofer.

Renovo Ultra Proofer

Waterproofs and Protects Your Soft Top

Description
Renovo Ultra Proofer re-establishes the convertible tops original 'as new' waterproof weather barrier.
The recently improved formulation now has the added benefits of UV factor protection and a mould/mildew growth inhibitor to ensure soft tops look like new for longer.
Before applying Ultra Proofer we recommend using Renovo Fabric Soft Top Cleaner according to the ‘severely soiled’ instructions on the bottle to thoroughly clean your convertible top.
Ultra Proofer will help to prevent the harmful penetration of everyday dirt into the fibres of new and old convertible top material and help to keep the re-colour provided by Soft Top Reviver fresher for even longer.
Take a look at our testimonials; you'll not be able buy a better convertible hood protection product!

Ultra Proofer - Application Instructions

Please note: It is advisable to test on an inconspicuous area of your convertible top prior to use, as some colours may appear lighter or darker after application.

Do not apply in direct sunlight, as this will cause the Ultra Proofer to dry out too quickly and produce an uneven result.

  1. Dry brush the soft top to remove any loose dust/dirt.
  2. Pour Ultra Proofer into a suitable container/bowl.
  3. Stir well before application.
  4. Apply Ultra Proofer with a new 5cm/2inch paintbrush ensuring that the fabric is completed wetted out. It is best to commence application in the centre of the soft top and as quickly as possible progress towards each side, the front and the back of the soft top. Wipe excess drips from paintwork, trims and glass with a damp cloth.
    Depending on the condition of the top a litre of Ultra Proofer is usually sufficient for two coats on an average size soft top. It is important to allow Ultra Proofer to dry between coats. Always ensure that you have enough Ultra Proofer to coat the soft top completely and that you will not run out half way through application!
  5. Allow the top to dry for approximately three hours, this will depend on the drying conditions. The Ultra Proofer may dry out more quickly if it is a warm day and may take longer to dry if it is a damp day.
  6. Wash out brush in warm, soapy water.

Do not take car out in rain/wet weather until the Ultra Proofer has completely dried.

The soft top is now water and stain repellent, will resist the growth of mould/mildew and is protected from harmful Ultra Violet rays.

To ensure best possible weatherproof protection we advise that Ultra Proofer is applied every six months.

Fabric Soft Top Cleaner

Do

  • Test on an inconspicuous area to ensure fabric is colourfast dyed.
  • Spray mist the soft top with water prior to application.
  • Use a clean paint brush to apply.
  • Leave Fabric Soft Top Cleaner on for 10-20 minutes for general cleaning.
  • Leave Fabric Soft Top Cleaner on for 40-60 minutes for stubborn dirt and to remove any previous waterproofing treatments.
  • Wear protective gloves whilst applying.
  • Use every 6-12 months.

Don’t

  • Use a power jet wash to clean a fabric soft top
  • Use a detergent based cleaner
  • Apply in direct sunlight.
  • Forget to shake the bottle prior to use.

Soft Top Reviver

Do

  • Ensure that the soft top is thoroughly cleaned.
  • Test on an inconspicuous area prior to treating the whole area.
  • Ensure that you have sufficient Reviver to complete a full coat.
  • Be diligent in removing previous waterproof coatings prior to application of Reviver.
  • Keep a soft damp cloth ready to wipe off any splashes or dribbles on paintwork and glass.
  • Work in a timely fashion to ensure that the edges of the freshly applied Reviver do not dry out too quickly.
  • Work from the centre outwards round and round the vehicle.
  • Apply to a dry top and allow Reviver to dry completely before applying further product or taking out in the rain.

Don’t

  • Forget to shake the bottle prior to use.
  • Dilute or mix the Reviver with any other product.
  • Apply the Reviver in direct sunlight or on a hot day that will cause the Reviver to dry too quickly.
  • Allow to dry on glass and paintwork.
  • Apply to a soft top that has been coated with a waterproofing agent without removing the proofer first.
  • Apply to vinyl soft tops or cars with modified paintwork.


Soft Top Ultra Proofer

Do

  • Ensure that the soft top is thoroughly cleaned.
  • Ensure that you have sufficient Ultra Proofer to complete a full coat.
  • Keep a soft damp cloth ready to wipe off any splashes or dribbles on paintwork and glass.
  • Work in a timely fashion to ensure that the edges of the freshly applied Ultra Proofer do not dry out too quickly.
  • Work from the centre outwards round and round the vehicle.
  • Apply to a dry top and allow Ultra Proofer to dry completely before applying further product or taking out in the rain.
  • Use every 6-12 months.

Don’t

  • Use on vinyl soft tops.
  • Forget to stir the Ultra Proofer prior to use.
  • Dilute or mix the Ultra Proofer with any other product.
  • Apply the Ultra Proofer in direct sunlight or on a hot day that will cause the Ultra Proofer to dry too quickly.
  • Allow to dry on glass and paintwork.
  • Apply to vinyl soft tops or cars with modified paintwork.
  • Apply water proofing agent prior to using Reviver unless the proofer is completely removed first.

Sunday, 23 May 2021

Upgrading My Roadster 100 Air Intake

 

Upgrading My Roadster 100 Air Intake

Upgrading My Roadster 100 Air Intake

Way back in 2018 I asked owners to check how their Air Intake Pipe was attached to the body of their car.

Most Roadsters left the factory with the pipe end left hanging over the Front Tie Bar with nothing across the end of the pipe.

A Typical Finish.

During the survey I came across this photo which inspired me to consider a similar finish to our own car.

The Air Intake Pipe has a shaped nacelle with a mesh insert to keep out large objects.

The other end of the Air Intake Tube joins onto what is the opening of the Air Filter Box.

The Splits in the rubber were put in by the factory to help slide the pipe over its nozzle end.

The Air Intake makes a Z turn under the Bonnet Hinge before it enters the Filter Box.

The Air Filter Box used on all of the Roadster 100's

For some months I have been making occasional searches of the internet trying to find a source of a similar Nacelle unit.

As is said, particularly where Google is concerned, If you don't ask the right question you are unlikely to get the answer you are looking for.

Member Gerald Ladkin, while showing his own new Air Intake Set Up, informed me that a company called 'Revotec' sold such items.

https://www.revotec.com/acatalog/Flexible-Ducting-and-Accessories.html

Then I came across a Facebook topic by 'Merlin Motorsport' and while studying their on line pages, there was the actual Nacelle & Gauze that I was seeking, along with suitably large Stainless Steel Jubilee Clips.

https://www.merlinmotorsport.co.uk/s/cooling/air-ducting/air-intake-ducts/aluminium-air-intake-ducts

Merlin, it turns out are suppliers of Revotec products.

I immediately placed my order for:

1 x Aluminium Air Inlet Polished to fit 102mm Hose.

1 x Aluminium Gauze to suit Air Inlets 102mm Silver

2 x Stainless Steel Hose Clips 100-120mm.

My Nacelle, Gauze and Hose Clip.

Showing the recess on to which the wired rubber hose fits

Before fitting, the Gauze has to be 'Glued' into the Air Intake, up against the step created by the recess.

I did this by mixing up a small spread of 'Araldite' adhesive into which I rolled the edge of the gauze.

Once the Gauze was set into the intake I added a little more Araldite around the edge using a wooden cocktail stick.

Any excess Araldite left on the sides may be carefully cleaned using a cloth soaked in Methylated Spirit.

The Gauze in place with the Araldite set overnight.

The next action was to reduce the length of the Wired Rubber Hose.

This was done using a Stanley Knife and Wire Cutters to snip the wire core.

I had removed the Upper Hose Clip with the intention of removing the tube to the bench but found that adhesive had been used preventing removal without damage.

I was quite surprised at what I found when I extracted the open end of the pipe.

Somewhere along the line, maybe when the car was stripped following my Damaged Sump, or when the Radiator was replaced, a mechanic has added this very open mesh using Cable Ties and the squashed the tube oval to jam it into the gap above the top Tie Bar.

The upper part of the hose has no wire so I counted 4 rings and chose to make the cut at that point.

I then trimmed the rough edge.

This length was chosen so that the Polished Intake would sit in the open area without fouling either any Engine Parts or the Bonnet and the Hose would be short enough to prevent any significant bounce.

I had also refitted the upper Hose Clip but this time I used it to cover over those unsightly slits in the rubber edge.

You may have noticed these small blocks.

Early on in the life of our car I noticed that the Air Filter Box would bounce and was removing paint from beneath the Bonnet Hinge edges.

Being a hoarder I kept these very dense Neoprene Blocks extracted from the ends of some Curtain Pole Boxes.

To create the cushion I cut them to size and joined and attached them with strips of Double Sided Adhesive Tape.

The Intake was attached after applying a film of 3 in 1 oil to the fixing edge to ease entry into the tube.

In my case I had ordered two Hose Clips which turned out to be narrow so I used both side by side.

I may well try and source a wide band to match the opposite end.

The View from the Intake Opening.

Still not as Pretty as the Red Car but better than that old tube.

Following my last service & MOT I noticed a significant improvement in 'Pull' from the new clean Air Filter Core which apparently had not been changed for a couple of years.

I am not expecting any performance improvement from this kit. Just a tidier engine bay.

Frank

The Morgan Centenary Trim Pack

  The Morgan Centenary Trim Pack During The Centenary of The Morgan Motor Company the owners of new Morgans in build were offered the variou...