Saturday, 12 October 2019

Winter Lay Up - Checklist - Holden Vintage & Classic

Vintage and Classic Car Winter Lay-Up Guide 
As tempting as it may be to throw an old blanket over your much loved vehicle and close the garage door, thinking that you will 'have a look at it over the Christmas holiday period' is simply not enough. The time to winter your car properly is now! Unless, of course, you intend to use it throughout the winter months. Here are a few simple steps that will reward you well come the spring.

1. Give it a good clean inside and out:
This really is the time to give your car a thorough wash and clean both the exterior and interior, using a high-pressure hose to remove accumulated road dirt from the underside. Leave it outside on a dry, windy day – just like your mother used to do with the washing!


2. Protect against rust: 
Apply grease to all mild steel brake and fuel pipes. This won't prevent corrosion from the inside but will certainly stop corrosion from the outside. Apply a good coating of wax to the bodywork, but don't polish it off (when you put the car back on the road another coat of wax and elbow grease will restore the shine). Likewise treat brightwork with either lacquer or a generous coating of wax or Vaseline. Spray mechanical parts with WD40 or similar. Apply a fresh coat of an underside rust preventative such as Waxoyl. Apply grease to all grease-points on steering, suspension and driveline.


3. Change engine oil:
Now is the time to change the oil and filter - before you put your car to bed. Old oil containing acidic material can damage your engine if left for a long time.


4. Stabilise the fuel:
Petrol: During extended periods of inactivity, modern ethanol-containing fuels will separate, leaving highly corrosive ethanol in all the 'low' points of your fuel system, ie at the bottom of your tank, in the pump, filter bowl and carburettors. If left, this will eventually cause permanent damage to your fuel system. Condensation forms inside empty tanks and causes them to rot through, so leave tanks half full or more  over the winter lay-up. If the car is standing on its road wheels give it a bounce from time to time to slosh the fuel around the tank. If the car is to be laid up for a year or more, drain the tank completely as the petrol is likely to become stale (you can tell by the peculiar smell) and contaminated with water.


5. Batteries:
Batteries will always suffer from inactivity. In fact, battery activity will actually extend life, Disconnect both positive and negative terminals, clean and grease the terminals, check and top up levels as necessary, and finally connect your battery conditioner, ensuring that you place the conditioner somewhere safe, and that there is no liklehood of the wires becoming trapped as you close the bonnet etc


6. Check Coolant: 
Anti-freeze levels need checking and if 2-3 years old need replacing with fresh:  Replenish the cooling system with the right proportion of water and anti-corrosion anti-freeze to cope with the coldest days of winter.


7. Protect Tyres:
Tyres get tired, so ether put up on axle stands or use tyre shoes, best over inflate by a couple of psi as well: You have the choice of putting your classic car up on blocks or to leave it standing on its road wheels. If it's simply winter storage it's probably easier to leave it resting on its wheels as this will enable you to roll the car out on to your drive-way to give it an airing from time to time.


8. Put to bed:
Make sure there is enough room to allow you to walk past without knocking it, Leave the hand brake off to avoid sticking brakes and finally, cover with an indoor cover. This helps to protect from damp, dust and general knocks and scratches.


9. Finally, don't forget to do a SORN Declaration (UK)
or may find yourself in receipt of a fine from the DVLA.


10. Should you decide to continue using your Classic throughout the winter period,
you could look at installing a Pre-heater system.
This allows you to warm the coolant in the engine prior to starting, thus eliminating the period of highest engine wear, and also ensuring the heater is up to temperature much quicker. Perfect to combat cold and frosty mornings!


 
Visit the holden website now
You are receiving this newsletter because you have previously purchased from us or have requested to receive our newsletter.
You can unsubscribe by clicking here.
Contact Us
Holden Vintage and Classic Ltd, Linton trading estate,
Bromyard, Herefordshire, HR7 4QT, England
Tel: 01885 488488

Cleaning and Maintenance of our MWS Wire Wheels

        Looking after your wheels over the winter

MWS Full Stainless Steel wire wheels are manufactured using state of the art technology. Special processes were developed after long years of Research and Development in making these wheels. Full stainless steel wheels are made of superior Austenitic grade stainless steel that has excellent protection against corrosion.
 
The Stainless Steel rims and shells are polished to a superior natural finish in special purpose machines. The hand polishing by highly skilled craftsmen compliments this.
 
The Stainless Steel spokes and nipples are electro polished to match the lustre and colour of the rims and shells.
 
The Wheels are specially treated as a final process to retain the lustre and colour.
 
100% inspection on finish on all the parts ensures only the best quality products are passed out.



The most important task is to give the wheels a thorough clean. 
Any foreign contaminants or surface rust if not removed can lead to severe corrosion. 
MWS Wire Wheels are craftsmen built products and to maintain their best condition in service the following advice should be followed. 

For All Finishes: (in addition to further specialised instructions below):
  • Allow the wheels to cool before cleaning
  • Do not use a pressure hose or washer
  • Do not use a car wash as the guidance tracks and/or hard brushes may cause damage
  • Do not use an abrasive polish or cleaner (such as T-Cut)
  • Regularly wash the wheels (on the car) with soap and water, rinse with clean water and dry off
  • Regularly remove the wheels from the vehicle and clean the entire wheel thoroughly to remove the corrosive dirt and brake dust which builds up over time
   
To support our customers in the care of their wire wheels MWS has produced a specialist cleaning kit containing: cleaning solution, protective solvent, dispenser, applicator brush and disposable gloves. 

To compliment our cleaning kit MWS offers a wire wheel cleaning brush for more stubborn marks.

How often you need to clean your wire wheels depends on the distance driven and the road conditions experienced. 

Due to brake dust and road salt being highly corrosive we strongly recommend thoroughly cleaning the wheels off the vehicle before putting into storage, for example over the winter.

Painted and Stainless Steel:

No additional care should be necessary

Chrome:

If the chrome appears tarnished:
  • Polish using a good quality non-abrasive chrome cleaner and a soft cloth
  • Rinse with clean water
  • Dry and wipe with a clean dry cloth to ensure all traces of cleaner are removed
If light rust spotting appears an acid-based chrome cleaner may be used; however, acid-based cleaners should not be used often as they are very strong. 

Take care to follow the manufacturer's instructions regarding treatment times and rinsing procedure. Damage caused by cleaning chemicals is not covered by our Warranty.

For storage over winter remove the wheels from the vehicle, clean thoroughly, dry completely and apply a light spray of WD40 (or equivalent) to help protect your wheels. 

If applying WD40 for storage then the wheel must be thoroughly cleaned before first use to ensure the oil does not compromise the brakes.

CAUTION – PLEASE READ THE MANUFACTURER'S INSTRUCTIONS AND ADVICE BEFORE USING ALL PRODUCTS

General good practice when using wire wheel cleaner is:
  • Wear protective gloves where possible and wash hands immediately after use
  • Avoid contact with skin and eyes
  • Keep all chemicals out of the reach of children and animals



Free of charge inspection
While your car is off the road for the winter it is the perfect time to have your wheels checked. MWS offer a free of charge inspection service that will report on the condition of each wheel. We can then advise on and perform any repair work that your wheels require.
For more information, pleasecontact us

Cleaning kit refills
MWS now offer refill packs for our Cleaning & Protection system. The cleaning solutionand finishing solution are both available individually.


Thursday, 25 July 2019

Dave's Plus 4 Front Chip Guards and Other Items

 Mr Bumble improvements - Phase 2.

A more relaxing day today. First a look at that rear panel with the rough holes, both for the exhaust hanger, but only one needed on a 4 cylinder.
This is the offside:


Hard to say whether this is best left alone or 'fixed', So I shaped some 1mm aluminium, and painted it, then used double sided tape and we'll see how we go with it:
Offside


Nearside


Here's the later badge. I'm not keen, preferring the older badge, although this one is not flaking.


So here is the replacement - a bit pricey though.


Now this comes flat, so you have to apply a bit of force to get the right curvature. I used masking tape to protect it, and used the vice. So now it's curved. The washers and nyloc's are from my stock.


It has a hollow back, so guess what?


The right hand hole has been slightly elongated.......


Hey presto - I like this a lot more.


Next I fitted some higher output headlamp bulbs. An offset screwdriver helps with this:


One screw and a twist is all it takes to remove the unit:


And I'm suffering whistling at moderate speed. This is often caused by air passing between the headlamp and the rim, although the Roadster doesn't do this.

So some self adhesive neoprene might just stop the whistle. We'll see.


Then I went back to the side-screen seals and tried a bit harder. This is all about trial and error, but double sided tape allows endless retry's.




Next I fitted some hood swivels which I picked up from e-bay, but came from John Gills. I had to check Grahams car because the swivel threaded rod was far too long for a 2012 car, which only has a single frame at that end.

Older Morgans have three frames to accommodate, which is why the threaded rod is so long. The photo which follows shows the original swivel. The black end is how much I had to cut from the swivel to get the right length:


And a dash clock................


And some painted drawing pins........


And that was all for today!!


A quick shot of the hood with neoprene added.

Today has been spent on the front mudflaps. I found some stainless off cuts in my scrap bin, left over from the Roadster. This kept hack sawing to a minimum. I don't like working with stainless, it's like a difficult woman. Hard to knock into shape and doesn't bend easily, but is unmatchable when sorted.
 
I've used a slightly different approach this time, using washers and bent washers to locate on the wing stays. Interestingly these wing stays are horizontal along the length, but the Roadster stays twist through 45 degrees, so doing the Roadster was harder to align.


Test fitted to nearside:




And offside - note proximity of exhaust.




The nearside is much easier, because there's no exhaust!
Here's the naked circuit board trial fitted.




And here it is glued and Dinitrolled on the back.


Corners can be rounded using a penny washer:


And here it is fitted:


The flash dilutes the colour - it's very black up there!


And now the test. All heat shielding was sourced from Agriemach. I had plenty in stock this time so no expense for once.

The exhaust is large diameter and close to the wing stay and mudflap.
First job was to measure up, do some cutting and fabricate a heat shield. 

This was a lot of faffing, but the bare skeleton looked like this - something from Wallace & Gromit in fact.
Thank goodness for pop rivets!






Next job was to apply a layer of insulating weave to the rear, and secure with Reflect-a-Cool:

Not obvious in the photos, but the aluminium heat shield is also covered in reflective weave.








Once trial fitted again, I could fit and trim the neoprene flap:

Here are some fitted shots:






I've used a similar set up on the Roadster (both sides) for four years without a problem, so I'm confident that this will be OK.
Whether you go for flaps or wing-liners, it's a job worth doing because the wings take a beating. You'll recall the lower edges of my rear wings were down to bare alloy and that's after 12,000 miles of normal use.

The Morgan Centenary Trim Pack

  The Morgan Centenary Trim Pack During The Centenary of The Morgan Motor Company the owners of new Morgans in build were offered the variou...